LM-330i A3 A4 Cold And Hot Mounting Laminator Photo Laminating
Machine
Plastic sealing machine, also known as the forming machine, glue
machine, laminating machine, is able to make up and down two floors
with glue powder coating membrane, the pressure of the
encapsulation sealing machine, it is mainly composed of rubber
roller, before and after heating temperature control system,
driving system, operation panel parts, such as encapsulation can
waterproof, prevent change, prevent fade, prevent breakage,
anti-fouling, and so on.
Specification
Laminating Width | 330mm (A3) |
Temperature | 180℃ |
Reverse | Yes |
Laminating speed | 550mm/min |
Dimension (L*W*H) | 525*210*110mm |
Roller Diameter | 25.5mm |
Press rollers | 4 |
Largest laminating thickness | 1.2mm |
Heating time | 3-5 minutes |
Output consuption | 600W |
Net weight | 6.2 Kg |
Driven type | Electric |
Features (Type: LM 330i):
- Metal case, strong and durable.
- LED display, super plastic film plate.
- Rapid heating, continuous use.
- Thick film thin film passes through uniformly.
- Environmental protection and energy saving, safe and reliable.
Metal fuselage, strong heat dissipation
Metal fuselage, safe and reliable, fire and lightning protection.
The LED display board
Knob temperature control, digital temperature control, temperature
accuracy.
Alloy gear
Alloy gear is not easy to wear, durable and reliable.
Four roll design, multi roll rolling
Pure silicone rubber roller, smooth and safe film, 24 hours
continuous film.
Plastic seal 250mic thick film
Thick film through uniform, through smooth, no bubbles.
Cold charge and hot charge, film in and film out
Cold loading and hot loading, film entry and film removal, one-key
operation, easy to use, suitable for public use.
Foundation non-slip rubber foot
The base is provided with non-slip foot pad, which makes the
machine stable.
Suggestions for thickness and temperature of plastic film:
- 200mic--180 ° C
- 170mic--170 ° C
- 150mic--160 ° C
- 125mic--140 ° C
- 100mic--130 ° C
- 80mic--110 ° C
- 70mic--100 ° C
- 60mic--90 ° C
- 50mic--80 ° C
- 40mic--70 ° C
Cold mounting -- no heating state (suitable for cold mounting of
film with a thickness of about 0.6mm). The above Suggestions can be
adjusted according to requirements.
Prepare:
Insert the plug into the power socket, turn on the power switch,
the power indicator light is on (red), and then the motor starts to
work normally. Turn on the preheat power and start preheating. The
temperature rose rapidly.
Temperature setting:
Set the button to the desired temperature and warm up for about 3
minutes. When the temperature rises to the set temperature, the
work light will be turned on and off many times. The temperature
tends to stabilize. At this time, plastic sealing can be performed.
In the process of work, the constant light will flicker, and there
will be repeated light and dark changes. This means that the lights
will constantly flicker, changing the lights and shadows
repeatedly. Refers to the internal constant temperature system
inside the machine. It is normal when the heating stops in the
switching heating state.
Application:
This machine is widely used to envelop ID cards, office documents,
photos and documentary cards. The cards packaged can resist against
water, alteration pollution, improve their strength and appearance
and extend their storage life.
- Metal shell
- Power indicator light
- Membrane Indicator
- Heating indicator
- Switch setting
- Temperature Regulating Switch
- Forward and Reverse Switch
- Paper entrance
- limit switch
Packing:
Single package size: 580*145*258mm
Single gross weight: 6.7 kg
Package Type:
The inner packaging is protected with anti-collision bubble paper,
sponge and foam. The outer packaging is packed in cartons and then
packed in wooden cases.
Port: Guangzhou / Foshan / Shenzhen / Ningbo
Quantity(Pieces) | 1 - 100 | 101 - 200 | 201 - 300 | >300 |
Est. Time(days) | 3 | 4 | 5 | To be negotiated |
